검색 상세

A study on characteristics of the gas outlet distribution in the gas sole flue of coke oven

코크스 오븐 Gas sole flue 내 연소 가스 분배 특성

신현준 (Hyunjun Shin, 포항공과대학교)

원문보기

초록 moremore
In the steel mill industry the improvement in the operation of coke ovens has received wide attention since it directly relates to the quality of the products, the performance of the units, and the energy saving. The operation to now usually relies on the experience and guidelines given in the begin...
In the steel mill industry the improvement in the operation of coke ovens has received wide attention since it directly relates to the quality of the products, the performance of the units, and the energy saving. The operation to now usually relies on the experience and guidelines given in the beginning without any attempt to analyze and improve the performance, especially gas outlet flow distribution within gas sole flue of the coke oven. It was mainly because there were no distributed measuring probes for this and no appropriate simulation tools for the analysis on the performance. Thus, only a few study has been reported on this issue. The factor directly affecting the coke quality stability and combustion control is gas outlet flow distribution. In this study, a simulation tool, computational fluid dynamics (CFD), was used for the effect of nozzle plate hole size and inlet flow rate on gas outlet flow distribution in the gas sole flue of coke oven. Then it was found that the inlet flow direction against the guide plate affect the outlet flow distribution and operating modes. And even if the hole size of the nozzle plate were increased linearly, gas outlet flow distribution pattern was not linear. In addition to, after door replacement or repair, the middle part of the nozzle plate hole should be resized for optimal control of combustion.
목차 moremore
1. 연구 배경
2. 연구 개요
3. 코크스 오븐 시스템
...
1. 연구 배경
2. 연구 개요
3. 코크스 오븐 시스템
3.1. 코크스 오븐 설비 타입 별 특징
3.2. 코크스 오븐 제조 공정
3.3. 코크스 오븐 연소 설비 구성
4. COKING PROCESS
4.1. 석탄 열분해 과정
4.2. 건류 온도가 코크스 품질에 미치는 영향
4.3. 코크스 오븐 연소 관리
5. 코크스 오븐 GAS SOLE FLUE의 CFD 시뮬레이션
5.1. Gas sole flue 설비 구성
5.2. CFD modeling tool
5.3. Basic assumption
5.4. Geometry of model
5.5. Mesh of model
5.6. Setup of model
6. 결과 분석 및 해석
6.1. Gas 및 air sole flue의 출구 유량 분포 차이 비교
6.2. Nozzle plate hole 크기 패턴 변화에 따른 출구 유량 분포 변화
6.3. Gas sole flue 출구 유량 분포 최적화
6.3.1. Middle flue 출구 유량 분포 최적화
6.3.2. End flue 출구 유량 분포 최적화
6.4. 분배관 입구 유량 변화에 따른 출구 유량 분포 변화
6.5. End flue nozzle plate hole 크기 변화에 따른 출구 유량 분포 변화
6.6. Middle flue nozzle plate hole 크기 변화에 따른 출구 유량 분포 변화
7. 결론
7.1. 연구 결과 및 조업 활용 방안
7.2. 추가 연구 방향